View S25FL008A0LNFI000_6730047.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

publication number s25fl008a_00 revision b amendment 3 issue date february 27, 2009 s25fl008a s25fl008a cover sheet 8-megabit cmos 3.0 volt flash memory with 50-mhz spi (serial pe ripheral interface) bus data sheet this product has been retired and is not recommended for designs. please contact your spansion representative for alternates. availability of this document is retained for reference and historical purposes only. notice to readers: this document states the current techni cal specifications regarding the spansion product(s) described herein. each product describ ed herein may be designated as advance information, preliminary, or full production. see notice on data sheet designations for definitions.
2 s25fl008a s25fl008a_00_b3 february 27, 2009 data sheet notice on data sheet designations spansion inc. issues data sheets with advance informati on or preliminary designations to advise readers of product information or int ended specifications throu ghout the product life cycle, including development, qualification, initial production, and fu ll production. in all cases, however, readers are encouraged to verify that they have the latest information before finalizing their design. the following descriptions of spansion data sheet designations are presented here to highlight their presence and definitions. advance information the advance information designation indicates that spansion inc. is developing one or more specific products, but has not committed any design to production. information pr esented in a document with this designation is likely to change, and in some cases, development on the product may discontinue. spansion inc. therefore places the following c onditions upon advance information content: ?this document contains information on one or mo re products under development at spansion inc. the information is intended to help you evaluate th is product. do not design in this product without contacting the factory. spansion inc. reserves t he right to change or discont inue work on this proposed product without notice.? preliminary the preliminary designation indicates that the produc t development has progressed such that a commitment to production has taken place. this designation covers several aspects of the product life cycle, including product qualification, initial produc tion, and the subsequent phases in t he manufacturing process that occur before full production is achieved. changes to the technical specifications presented in a preliminary document should be expected while keeping these as pects of production under consideration. spansion places the following conditions upon preliminary content: ?this document states the current technical sp ecifications regarding the spansion product(s) described herein. the preliminary status of this document indicates that product qualification has been completed, and that initial production has begun. due to the phases of the manufacturing process that require maintaining efficiency and quality, this doc ument may be revised by subsequent versions or modifications due to changes in technical specifications.? combination some data sheets contain a combination of products with different designations (advance information, preliminary, or full production). this type of docum ent distinguishes these prod ucts and their designations wherever necessary, typically on the first page, t he ordering information page, and pages with the dc characteristics table and the ac erase and program ta ble (in the table notes). the disclaimer on the first page refers the reader to the notice on this page. full production (no designation on document) when a product has been in production for a period of time such that no changes or only nominal changes are expected, the preliminary designation is remove d from the data sheet. nominal changes may include those affecting the number of ordering part numbers available, such as t he addition or deletion of a speed option, temperature range, package type, or v io range. changes may also include those needed to clarify a description or to correct a typographical error or incorre ct specification. spansion inc. applies the following conditions to documents in this category: ?this document states the current technical sp ecifications regarding the spansion product(s) described herein. spansi on inc. deems the products to have been in sufficient production volume such that subsequent versions of this document are not expected to change. however, typographical or specification corrections, or mo difications to the valid comb inations offered may occur.? questions regarding these docum ent designations may be directed to your local sales office.
this document states the current technical specifications regarding the spansion product(s) described herein. spansion inc. dee ms the products to have been in sufficient pro- duction volume such that subsequent versions of this document are not expected to change. however, typographical or specificati on corrections, or modifications to the valid com- binations offered may occur. publication number s25fl008a_00 revision b amendment 3 issue date february 27, 2009 this product has been retired and is not recommended for designs . please contact your spansion representative for alternates. availability of this document is retained for reference and historical purposes only. distinctive characteristics architectural advantages ? single power supply operation ? full voltage range: 2.7 to 3.6 v read and program operations ? memory architecture ? sixteen sectors with 512 kb each ? program ? page program (up to 256 bytes) in 1.5 ms (typical) ? program operations are on a page by page basis ? erase ? 0.5 s typical sector erase time ? 6 s typical bulk erase time ? cycling endurance ? 100,000 cycles per sector typical ? data retention ? 20 years typical ? device id ? jedec standard two-byte electronic signature ? res command one-byte electronic signature for backward compatibility ? process technology ? manufactured on 0.20 m mirrorbit ? process technology ? package option ? industry standard pinouts ? 8-pin so package (208 mils) ? 8-contact uson package (5 x 6mm) performance characteristics ? speed ? 50 mhz clock rate (maximum) ? power saving standby mode ? standby mode 20 a (typical) ? deep power-down mode 1.5 a (typical) memory protection features ? memory protection ? w# pin works in conjunction with status register bits to protect specified memory areas ? status register block protection bits (bp2, bp1, bp0) in status register configure parts of memory as read-only software features ? spi bus compatible serial interface general description the s25fl008a is a 3.0 volt (2.7 v to 3.6 v), single- power-supply flash memory device. the device consists of 16 sectors, each with 512 kb memory. the device accepts data written to si (serial input) and outputs data on so (seria l output). the devices are designed to be programmed in-system wi th the standard system 3.0 volt v cc supply. the memory can be programmed 1 to 256 bytes at a time, using the page program command. the device supports sector erase and bulk erase commands. each device requires only a 3.0 volt power supply (2.7 v to 3.6 v) for both read and write functions. internally generated and regulated voltages are provided for the program operations. this device does not require a v pp supply. s25fl008a 8-megabit cmos 3.0 volt flash memory with 50-mhz spi (serial pe ripheral interface) bus data sheet
4 s25fl008a s25fl008a_00_b3 february 27, 2009 data sheet table of contents distinctive characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 general description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1. block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2. connection diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3. input/output descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4. logic symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 5. ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5.1 valid combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 6. spansion spi modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7. device operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 7.1 byte or page programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 7.2 sector erase / bulk erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 7.3 monitoring program or erase operations using the stat us register . . . . . . . . . . . . . . . . . . 11 7.4 active power and standby power modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 7.5 status register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 7.6 data protection modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 7.7 hold mode (hold#) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 8. sector address table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 9. command definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 9.1 read data bytes (read) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 9.2 read data bytes at higher speed (fast_read) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 9.3 read identification (rdid) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 9.4 write enable (wren) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 9.5 write disable (wrdi). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 9.6 read status register (rdsr) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 9.7 write status register (wrsr). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 9.8 page program (pp) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 9.9 sector erase (se) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 9.10 bulk erase (be) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 9.11 deep power down (dp). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 9.12 release from deep power down (res) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 10. power-up and power-down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 11. initial delivery state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 12. absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 13. operating ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 14. dc characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 15. test conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 16. ac characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 17. physical dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 17.1 soc 008 wide?8-pin plastic small outline 208 mils body width package . . . . . . . . . . . . . 30 17.2 uson 8l (5 x 6 mm) no-lead package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 18. revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
february 27, 2009 s25fl008a_00_b3 s25fl008a 5 data sheet figures figure 2.1 8-pin plastic small outline package (so) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 figure 2.2 8l uson (5 x 6 mm 2 ) package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 figure 6.1 bus master and memory devices on the spi bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 figure 6.2 spi modes supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 figure 7.1 hold mode operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 figure 9.1 read data bytes (read) command sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 figure 9.2 read data bytes at higher speed (fast_read) command sequence . . . . . . . . . . . . . . . 15 figure 9.3 read identification (rdid) command sequence a nd data-out sequence . . . . . . . . . . . . . 16 figure 9.4 write enable (wren) command sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 figure 9.5 write disable (wrdi) command sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 figure 9.6 read status register (rdsr) command sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 figure 9.7 write status register (wrsr) command sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 figure 9.8 page program (pp) command sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 figure 9.9 sector erase (se) command sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 figure 9.10 bulk erase (be) command sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 figure 9.11 deep power down (dp) command sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 figure 9.12 release from deep power down (res) command se quence . . . . . . . . . . . . . . . . . . . . . . . 22 figure 9.13 release from deep power down and read electronic signature (res) command sequence 23 figure 10.1 power-up timing diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 figure 12.1 maximum negative overshoot waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 figure 12.2 maximum positive overshoot waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 5 figure 15.1 ac measurements i/o waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 figure 16.1 ac characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 figure 16.2 spi mode 0 (0,0) input timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 figure 16.3 spi mode 0 (0,0) output timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 figure 16.4 hold# timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 figure 16.5 write protect setup and hold timing during wr sr when srwd=1 . . . . . . . . . . . . . . . . . . 29
6 s25fl008a s25fl008a_00_b3 february 27, 2009 data sheet tables table 5.1 s25fl008a valid combinations table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 table 7.1 s25fl008a protected area sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 table 8.1 s25fl008a device organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 table 8.2 s25fl008a sector address table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 table 9.1 read identification (rdid) data-out sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 table 9.2 s25fl008a status register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 table 9.3 protection modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 table 9.4 command definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 table 10.1 power-up timing characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 table 12.1 absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 table 13.1 operating ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 table 14.1 dc characteristics (cmos compatible) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 table 15.1 test specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
february 27, 2009 s25fl008a_00_b3 s25fl008a 7 data sheet 1. block diagram 2. connection diagrams figure 2.1 8-pin plastic small outline package (so) figure 2.2 8l uson (5 x 6 mm 2 ) package s ram p s lo g ic array - l array - r rd data path io x d e c c s # s ck s i s o gnd hold# v cc 1 2 3 4 c s # s o w# gnd s i s ck hold# vcc 5 6 7 8 1 2 3 4 5 6 7 8 cs# vcc so hold# sck si gnd w#
8 s25fl008a s25fl008a_00_b3 february 27, 2009 data sheet 3. input/output descriptions 4. logic symbol signal i/o description so output signal data output: transfers data serially out of the device on the falling edge of sck. si input serial data input : transfers data serially into the devi ce. device latches commands, addresses, and program data on si on the rising edge of sck. sck input serial clock : provides serial interface timing. latches commands, addresses, and data on si on rising edge of sck. triggers output on so after the falling edge of sck. cs# input chip select : places device in active power mode when driven low. deselects device and places so at high impedance when high. after power-up, device requires a falling edge on cs# before any command is written. device is in standby mode when a program, erase, or write status register operation is not in progress. hold# input hold : pauses any serial communication with the de vice without deselecting it. when driven low, so is at high impedance, and all input at si and sck are ignored. requires that cs# also be driven low. w# input write protect : protects the memory area specified by status register bits bp2:bp0. when driven low, prevents any program or erase command from altering the data in the protected memory area. v cc input supply voltage gnd input ground c s # s o w# gnd s i s ck hold# v cc
february 27, 2009 s25fl008a_00_b3 s25fl008a 9 data sheet 5. ordering information this product has been retired and is not recommend ed for designs. please contact your spansion representative for alternates. avail ability of this document is retained for reference and historical purposes only. the ordering part number is formed by a valid combination of the following: notes 1. contact your local sales office for availability. 2. package marking omits leading ?s25? and speed, package, and model number form. 3. a for standard package (non-pb free); f for pb-free package. 5.1 valid combinations table 5.1 lists the valid combinations configurations planned to be supported in volume for this device. s25fl 008 a 0l m a i 00 1 packing type (note 1) 0 = tray 1 = tube 3 = 13? tape and reel model number (additional ordering options) 00 = no additional ordering options temperature range i = industrial (?40c to + 85c) package materials a = standard f = lead (pb)-free package type m = 8-pin plastic small outline package n = 8-contact uson package speed 0l = 50 mhz device technology a = 0.20 m mirrorbit ? process technology density 008 = 8 mbit device family s25fl spansion tm memory 3.0 volt-only, serial peripheral interface (spi) flash memory table 5.1 s25fl008a valid combinations table s25fl008a valid combinations package marking (note 2) base ordering part number speed option package & temperature model number packing type s25fl008a 0l mai, mfi nai, nfi 00 0, 1, 3 (note 1) fl008a + (temp) + (note 3) 00
10 s25fl008a s25fl008a_00_b3 february 27, 2009 data sheet 6. spansion spi modes a microcontroller can use either of its two spi mo des to control spansion spi flash memory devices: ? cpol = 0, cpha = 0 (mode 0) ? cpol = 1, cpha = 1 (mode 3) input data is latched in on the rising edge of sck, and output data is available from the falling edge of sck for both modes. when the bus master is in standby mode, sck is as shown in figure 6.2 for each of the two modes: ? sck remains at 0 for (cpol = 0, cpha = 0 mode 0) ? sck remains at 1 for (cpol = 1, cpha = 1 mode 3) figure 6.1 bus master and memory devices on the spi bus note the write protect (w#) and hold (hold#) signals should be driven high (logic level 1) or low (logic level 0) as appropriate. figure 6.2 spi modes supported s pi interf a ce with (cpol, cpha) = (0, 0) or (1, 1) b us m as ter c s3 c s 2c s 1 s pi memory device s pi memory device s pi memory device c s # w# hold# c s # w# hold# c s # w# hold# s ck s o s i s ck s o s i s ck s o s i s o s i s ck m s b m s b s ck s ck s i s o cpha cpol 00 11 c s # mode 0 mode 3
february 27, 2009 s25fl008a_00_b3 s25fl008a 11 data sheet 7. device operations all spansion spi devices (s25fl-a) accept an d output data in bytes (8 bits at a time). 7.1 byte or page programming programming data requires two commands: write enable (wren), which is one byte, and a page program (pp) sequence, which consists of four bytes plus da ta. the page program sequence accepts from 1 byte up to 256 consecutive bytes of data (which is the size of one page) to be programmed in one operation. programming means that bits can either be left at 0, or programmed from 1 to 0. changing bits from 0 to 1 requires an erase operation. before this can be applied, the bytes of the memory need to be first erased to all 1?s (ffh) before any programming. 7.2 sector erase / bulk erase the sector erase (se) and bulk erase (be) commands set all the bits in a sector or the entire memory array to 1. while bits can be individually programmed from a 1 to 0, erasing bits from 0 to 1 must be done on a sector-wide (se) or array-wide (be) level. 7.3 monitoring program or erase oper ations using the status register the host system can determine when a program or erase operation is co mplete by monitoring the write in progress (wip) bit in the status register. the read from status register command provides the state of the wip bit. 7.4 active power and standby power modes the device is enabled and in the active power mode when chip select (cs#) is low. when cs# is high, the device is disabled, but may still be in the active po wer mode until all program, erase, and write status register operations have completed. the device then goes into the standby power mode, and power consumption drops to i sb . the deep power down (dp) command provides additional data protection against inadvertent signals. after writing the dp command, the device ignores any further program or erase commands, and reduces its power consumption to i dp . 7.5 status register the status register contains the st atus and control bits that can be read or set by specific commands ( table 9.2, s25fl008a status register on page 17 ): ? write in progress (wip): indicates whether the device is performi ng a write status register, program or erase operation. ? write enable latch (wel): indicates the status of the internal write enable latch. ? block protect (bp2, bp1, bp0): non-volatile bits that define memory area to be software-protected against program and erase commands. ? status register write disable (srwd): places the device in the hardwa re protected mode when this bit is set to 1 and the w# input is driven low. in this m ode, the non-volatile bits of the status register (srwd, bp2, bp1, bp0) become read-only bits.
12 s25fl008a s25fl008a_00_b3 february 27, 2009 data sheet 7.6 data protection modes spansion spi flash memory devices provi de the following data protection methods: ? the write enable (wren) command: must be written prior to any command that modifies data. the wren command sets the write enable latch (wel ) bit. the wel bit resets (disables writes) on power-up or after the device completes the following commands : ? page program (pp) ? sector erase (se) ? bulk erase (be) ? write disable (wrdi) ? write status register (wrsr) ? software protected mode (spm): the block protect (bp2, bp1, bp0) bits define the section of the memory array that can be read but not programmed or erased. table 7.1 shows the sizes and address ranges of protected areas that are defi ned by status register bits bp2:bp0. ? hardware protected mode (hpm): the write protect (w#) input and the status register write disable (srwd) bit together provide write protection. ? clock pulse count: the device verifies that all program, er ase, and write status register commands consist of a clock pulse count that is a multiple of eight before executing them. 7.7 hold mode (hold#) the hold input (hold#) stops any serial communicatio n with the device, but does not terminate any write status register, program or erase operation that is currently in progress. the hold mode starts on the falling edge of hold# if sck is also low (see figure 7.1 on page 13 , standard use). if the falling edge of hold# does not occur while sc k is low, the hold mode begins after the next falling edge of sck (non-standard use). the hold mode ends on the rising edge of hold# signal (s tandard use) if sck is also low. if the rising edge of hold# does not occur while sck is low, the hold mode ends on the next falling edge of clk (non- standard use) see figure 7.1 . the so output is high impedance, and the si and sck in puts are ignored (don?t care) for the duration of the hold mode. cs# must remain low for the entire duration of the hold mode to ensure that the device internal logic remains unchanged. if cs# goes high while the device is in the ho ld mode, the internal logic is reset. to prevent the device from reverting to the hold mode when device communication is resumed, hold# must be held high, followed by driving cs# low. table 7.1 s25fl008a protected area sizes status register block protect bits memory array protected portion of total memory area bp2 bp1 bp0 protected address range protected sectors unprotected address range unprotected sectors 0 0 0 none (0) 00000h?fffffh sa15:sa0 0 0 0 1 f0000h?fffffh (1) sa15 00000h?effffh sa14:sa0 1/16 0 1 0 e0000h?fffffh (2) sa15:sa14 00000h?dffffh sa13:sa0 1/8 0 1 1 c0000h?fffffh (4) sa15:sa12 00000h?bffffh sa11:sa0 1/4 1 0 0 80000h?fffffh (8) sa15:sa8 00000h?7ffffh sa7:sa0 1/2 1 0 1 00000h?fffffh (16) sa15:sa0 none none all 1 1 0 00000h?fffffh (16) sa15:sa0 none none all 1 1 1 00000h?fffffh (16) sa15:sa0 none none all
february 27, 2009 s25fl008a_00_b3 s25fl008a 13 data sheet figure 7.1 hold mode operation 8. sector address table table 8.1 shows the size of the memory array, sectors, and pages. the device uses pages to cache the program data before the data is programmed into the memory array. each page or byte can be individually programmed (bits are changed from 1 to 0). the data is erased (bits are changed from 0 to 1) on a sector- or device-wide basis using the se or be commands. table 8.2 shows the starting and ending address for each sector. the complete set of sectors compri ses the memory array of the flash device. s ck hold# hold condition ( s t a nd a rd us e) hold condition (non- s t a nd a rd us e) table 8.1 s25fl008a device organization each device has each sector has each page has 1,048,576 65,536 256 bytes 4,096 256 ? pages 16 ? ? sectors table 8.2 s25fl008a sector address table sector address range sa15 f0000h fffffh sa14 e0000h effffh sa13 d0000h dffffh sa12 c0000h cffffh sa11 b0000h bffffh sa10 a0000h affffh sa9 90000h 9ffffh sa8 80000h 8ffffh sa7 70000h 7ffffh sa6 60000h 6ffffh sa5 50000h 5ffffh sa4 40000h 4ffffh sa3 30000h 3ffffh sa2 20000h 2ffffh sa1 10000h 1ffffh sa0 00000h 0ffffh
14 s25fl008a s25fl008a_00_b3 february 27, 2009 data sheet 9. command definitions the host system must shift all commands, addresses, and data in and out of the device, beginning with the most significant bit. on the first rising edge of sck a fter cs# is driven low, the device accepts the one-byte command on si (all commands are one byte long), most significant bit first. each successive bit is latched on the rising edge of sck. table 9.4 on page 23 lists the complete set of commands. every command sequence begins with a one-byte comm and code. the command may be followed by address, data, both, or nothing, depending on the comma nd. cs# must be driven high after the last bit of the command sequence has been written. the read data bytes (read), read status regi ster (rdsr), read data bytes at higher speed (fast_read) and read identification (rdid) command sequences are followed by a data output sequence on so. cs# can be driven high after any bit of th e sequence is output to terminate the operation. the page program (pp), sector erase (se), bulk eras e (be), write status regi ster (wrsr), write enable (wren), or write disable (wrdi) commands require that cs# be driven high at a byte boundary, otherwise the command is not executed. since a byte is composed of eight bits, cs# must therefore be driven high when the number of clock pulses after cs# is driven low is an exact multiple of eight. the device ignores any attempt to access the memory array during a write status register, program, or erase operation, and continue s the operation uninterrupted. 9.1 read data bytes (read) the read data bytes (read) command reads data from the memory array at the frequency (f sck ) presented at the sck input, with a maximum speed of 33 mhz. the host system must first select the device by driving cs# low. the read command is then written to si, followed by a 3-byte address (a23-a0). each bit is latched on the rising edge of sck. the memory array dat a, at that address, are out put serially on so at a frequency f sck , on the falling edge of sck. figure 9.1 and table 9.4 on page 23 detail the read command sequence. the first byte specified can be at any location. the device automatically increments to the next higher address after each byte of data is output. the entire memory array can therefore be read with a single read command. when the highest address is reached, the address counter reverts to 00000h, al lowing the read sequence to continue indefinitely. the read command is terminated by driving cs# high at any time during data output. the device rejects any read command issued while it is executing a progr am, erase, or write status register operation, and continues the operation uninterrupted. figure 9.1 read data bytes (read) command sequence comm a nd 24-bit addre ss hi-z m s b m s b d a t a o u t 1 d a t a o u t 2 0 3 1 3 2 33 3 4 3 5 3 6 3 7 38 3 9 3 0 29 2 8 10 9 8 7 6 5 4 3 2 1 7 6 5 2 3 22 21 4 3 2 1 0 3 2 10 7 s o s i s ck c s # mode 3 mode 0
february 27, 2009 s25fl008a_00_b3 s25fl008a 15 data sheet 9.2 read data bytes at higher speed (fast_read) the fast_read command reads data from the memory array at the frequency (f sck ) presented at the sck input, with a maximum speed of 50 mhz. the host system must first select the device by driving cs# low. the fast_read command is then written to si, followed by a 3-byte address (a23-a0) and a dummy byte. each bit is latched on the rising edge of sck. the memory arra y data, at that address, are output serially on so at a frequency f sck , on the falling edge of sck. the fast_read command sequence is shown in figure 9.2 and table 9.4 on page 23 . the first byte specified can be at any location. the device automaticall y increments to the next higher address after each byte of data is output. the entire memory array ca n therefore be read with a single fast_read command. when the highest address is reached, the address coun ter reverts to 00000h, allowing the read sequence to continue indefinitely. the fast_read command is terminated by driving cs# high at any time during data output. the device rejects any fast_read command issued while it is ex ecuting a program, erase, or write status register operation, and continues the operation uninterrupted. figure 9.2 read data bytes at higher speed (fast_read) command sequence 9.3 read identification (rdid) the read identification (rdid) comm and outputs the one-byte manufacturer identificat ion, followed by the two-byte device id entification, to the host system. jedec assigns the manufacturer identification byte; for spansion devices it is 01h. the device manufacturer assigns the device identification: the first byte prov ides the memory type; the second byte indicates the memory capacity. see table 9.1 on page 16 or table 9.4 on page 23 for device id data. the host system must first select the device by drivin g cs# low. the rdid command is then written to si, and each bit is latched on the rising edge of sck. t he 24-bit device identification data is output from the memory array on so at a frequency f sck , on the falling edge of sck. the rdid command sequence is shown in figure 9.3 on page 16 and table 9.4 on page 23 . driving cs# high after the device identification data has been read at least once terminates the read_id command. driving cs# high at any time during data output also terminat es the rdid operation. the device rejects any rdid command issued while it is ex ecuting a program, erase, or write status register operation, and continues the operation uninterrupted. c s # s ck s i s o comm a nd 24-bit addre ss d u mmy byte hi-z data out 1 data out 2 m s b m s b 01 2 3 4 56 7 8 9 10 2 8 29 3 0 3 1 3 2 33 3 4 3 5 3 6 3 7 38 3 9 40 41 42 4 3 44 45 46 47 2 3 22 21 3 2 1 0 7 654 3 2 1 0 7 6 5 4 3 210 7 mode 3 mode 0
16 s25fl008a s25fl008a_00_b3 february 27, 2009 data sheet figure 9.3 read identification (rdid) comma nd sequence and data-out sequence 9.4 write enable (wren) the write enable (wren) command (see figure 9.4 ) sets the write enable latch (wel) bit to a 1, which enables the device to accept a write status register , program, or erase command . the wel bit must be set prior to every page program (pp), erase (se or be) and write stat us register (wrsr) command. the host system must first drive cs# low, writ e the wren command, and then drive cs# high. figure 9.4 write enable (wren) command sequence table 9.1 read identification (rdi d) data-out sequence manufacturer identification device identification memory type memory capacity 01h 02h 13h 0 1 2 456 7 8 9 10 11 12 13 14 15 16 17 18 28 29 30 31 command msb manufacturer identification device identification hi-z 0 1 2 3 13 14 15 cs# sck si so 3 mode 3 mode 0 c s # s ck s i s o hi-z comm a nd 01 2 3 45 67 mode 3 mode 0
february 27, 2009 s25fl008a_00_b3 s25fl008a 17 data sheet 9.5 write disable (wrdi) the write disable (wrdi) command (see figure 9.5 on page 17 ) resets the write enable latch (wel) bit to a 0, which disables the device from accepting a write status register, program, or erase command. the host system must first drive cs# low, write the wrdi command , and then drive cs# high. any of following conditions resets the wel bit: ? power-up ? write disable (wrdi) command completion ? write status register (wrsr) command completion ? page program (pp) command completion ? sector erase (se) command completion ? bulk erase (be) command completion figure 9.5 write disable (wrdi) command sequence 9.6 read status register (rdsr) the read status register (rds r) command outputs the state of the status register bits. table 9.2 shows the status register bits and their functions. the rdsr command may be written at any time, even wh ile a program, erase, or write status register operation is in progress. the host system should check the write in progress (wip) bit before sending a new command to the device if an operation is already in progress. figure 9.6 shows the rdsr command sequence, which also shows that it is possible to read the status register continuously until cs# is driven high. 0 1 2 3 4 5 6 7 comm a nd c s # hi-z s ck s i s o mode 3 mode 0 table 9.2 s25fl008a status register bit status register bit bit function description 7 srwd status register write disable 1 = protects when w# is low 0 = no protection, even when w# is low 6 ? ? not used 5 ? ? not used 4bp2 block protect 000?111 = protects upper half of address range in 5 sizes. see table 7.1 on page 12 . 3bp1 2bp0 1 wel write enable latch 1 = device accepts write status register, program, or erase commands 0 = ignores write status register, program, or erase commands 0 wip write in progress 1 = device busy. a write status register, program, or erase operation is in progress 0 = ready. device is in standby mode and can accept commands.
18 s25fl008a s25fl008a_00_b3 february 27, 2009 data sheet figure 9.6 read status register ( rdsr) command sequence the following describes the status and co ntrol bits of the status register. write in progress (wip) bit: indicates whether the device is busy performing a write status register, program, or erase operation. this bit is read-only, and is controlled internally by the device. if wip is 1, one of these operations is in progress; if wip is 0, no such operation is in progress. write enable latch (wel) bit: determines whether the device will accept and execute a write status register, program, or erase command. when set to 1, the device accepts these commands; when set to 0, the device rejects the commands. this bit is set to 1 by writing the wren command, and set to 0 by the wrdi command, and is also automatically reset to 0 after the completion of a write status register, program, or erase operation. wel cannot be directly set by the wrsr command. block protect (bp2, bp1, bp0) bits: define the portion of the memory area that will be protected against any changes to the stored data. the write status register (wrsr) command controls these bits, which are non-volatile. when one or more of these bits is set to 1, the corresponding memory area (see table 7.1 on page 12 ) is protected against page program (pp) and se ctor erase (se) command s. if the hardware protected mode is enabled, bp2:bp0 cannot be changed. the bulk erase ( be) command is executed only if all block protect (bp2, bp1, bp0) bits are 0. status register writ e disable (srwd) bit: provides data protection when used together with the write protect (w#) signal. when srwd is set to 1 and w# is driven low, the device ente rs the hardware protected mode. the non-volatile bits of the status register (srwd, bp2, bp1, bp0) become read-only bits and the device ignores any write status register (wrsr) command. 9.7 write status register (wrsr) the write status register (wrsr) command changes the bits in the status register. a write enable (wren) command, which itself sets the write enable latch (wel) in the status register, is required prior to writing the wrsr command. table 9.2, s25fl008a status register on page 17 shows the status register bits and their functions. the host system must drive cs# low, write the wrsr command, and the appropriate data byte on si ( figure 9.7 ). the wrsr command cannot change the state of the write enable latch (bit 1). the wren command must be used for that purpose. bit 0 is a st atus bit controlled internally by the flash device. bits 6 and 5 are always read as 0 and have no user significance. the wrsr command also controls the value of the stat us register write disable (srwd) bit. the srwd bit and w# together place the device in the hardware protected mode (hpm). the device ignores all wrsr commands once it enters the hardware protected mode (hpm). table 9.3 on page 19 shows that w# must be driven low and the srwd bit must be 1 for this to occur. comm a nd hi-z m s b m s b s t a t us regi s ter o u t s t a t us regi s ter o u t 0 15 14 1 3 12 11 10 9 8 7 6 5 4 3 2 1 7 6 5 4 3 2 10 7 6 5 4 3 2 1 0 7 s o s i s ck c s # mode 3 mode 0
february 27, 2009 s25fl008a_00_b3 s25fl008a 19 data sheet figure 9.7 write status register (wrsr) command sequence note as defined by the values in the block protect (bp2, bp1, bp0) bits of the status register, as shown in table 7.1 on page 12 . table 9.3 shows that neither w# or srwd bit by themselves can enable hpm. the device can enter hpm either by setting the srwd bit after driving w# low, or by driving w# low after setting the srwd bit. however, the device disables hpm only when w# is driven high. note that hpm only protects against changes to the status register. since bp2 :bp0 cannot be changed in hpm, the size of the protected area of the memory array cannot be changed. note that hpm provides no protection to the memory array area outside that specified by bp2:bp0 (software protected mode, or spm). if w# is permanently tied high, hpm can never be acti vated, and only the spm (bp2:bp0 bits of the status register) can be used. 9.8 page program (pp) the page program (pp) command changes specified bytes in the memory array (from 1 to 0 only). a wren command is required prior to writing the pp command. the host system must drive cs# low, and then write the pp command, three address bytes, and at least one data byte on si. cs# must be driven low for the enti re duration of the pp sequence. the command sequence is shown in figure 9.8 on page 20 and table 9.4 on page 23 . the device programs only the last 256 data bytes sent to the device. if the number of data bytes exceeds this limit, the bytes sent before the last 256 bytes are disca rded, and the device begins programming the last 256 bytes sent at the starting address of the specified page. this may result in data being programmed into different addresses within the same page than expected. if fewer than 256 data bytes are sent to device, they are correctly programmed at the requested addresses. the host system must drive cs# high after the device has latc hed the 8th bit of the data byte, otherwise the device does not execute the pp comma nd. the pp operation begins as soon as cs# is driven high. the device internally controls the timing of th e operation, which requires a period of t pp . the status register may be read to check the value of the write in progress (w ip) bit while the pp operation is in progress. the wip bit is 1 during the pp operation, and is 0 when the oper ation is completed. the device internally resets the write enable latch to 0 before the operation co mpletes (the exact timing is not specified). the device does not execute a page pr ogram (pp) command that specifies a page that is protected by the block protect bits (bp2:bp0) (see table 7.1 on page 12 ). table 9.3 protection modes w# signal srwd bit mode write protection of the status register protected area (see note) unprotected area (see note) 11 software protected (spm) status register is writable (if the wren command has set the wel bit). the values in the srwd, bp2, bp1 and bp0 bits can be changed. protected against program and erase commands ready to accept page program and sector erase commands 10 00 01 hardware protected (hpm) status register is hardware write protected. the values in the srwd, bp2, bp1 and bp0 bits cannot be changed. protected against program and erase commands ready to accept page program and sector erase commands hi-z m s b comm a nd s t a t us regi s ter in c s # s ck s i s o 0 12 3 4 5 6 7 7654 3 210 8 9 10 11 12 1 3 14 15 mode 0 mode 3
20 s25fl008a s25fl008a_00_b3 february 27, 2009 data sheet figure 9.8 page program (pp) command sequence 9.9 sector erase (se) the sector erase (se) command sets all bits at all addre sses within a specified sector to a logic 1. a wren command is required prior to writing the pp command. the host system must drive cs# low, and then write the se command plus three address bytes on si. any address within th e sector (see table 7.1 on page 12 ) is a valid address for the se command. cs# must be driven low for the entire duration of the se sequence. the command sequence is shown in figure 9.9 and table 9.4 on page 23 . the host system must drive cs# high after the device has latc hed the 8th bit of the se command, otherwise the device does not execute the co mmand. the se operation begins as s oon as cs# is driven high. the device internally controls the timing of th e operation, which requires a period of t se . the status register may be read to check the value of the write in progress (w ip) bit while the se operation is in progress. the wip bit is 1 during the se operation, and is 0 when the oper ation is completed. the device internally resets the write enable latch to 0 before the operation co mpletes (the exact timing is not specified). the device does not execute an se command that specifie s a sector that is protec ted by the block protect bits (bp2:bp0) (see table 7.1 on page 12 ). figure 9.9 sector erase (se) command sequence 0 3 4 33 3 2 3 1 3 0 29 2 8 10 9 8 7 6 5 4 3 2 1 3 5 3 6 3 7 38 3 9 46 45 44 4 3 42 41 40 47 4 8 49 50 51 52 5 3 54 55 207 3 2072 2076 2075 2074 2079 207 8 2077 2 3 22 21 3 21 07 6 5 4 3 2 1 0 d a t a byte 1 24-bit addre ss comm a nd d a t a byte 2 d a t a byte 3 d a t a byte 256 m s b m s b m s b m s b m s b s ck s i s ck s i 7 65 4 3 2 1 0 76 54 3 21 0 7 6 5 4 3 210 c s # c s # mode 0 mode 3 c s # s ck s i s o m s b comm a nd 24- b it addre ss 01 2 3 45 67 8 910 2 8 29 3 0 3 1 2 3 22 21 3 2 1 0 hi-z mode 0 mode 3
february 27, 2009 s25fl008a_00_b3 s25fl008a 21 data sheet 9.10 bulk erase (be) the bulk erase (be) command sets all the bits within the entire memory array to logic 1s. a wren command is required prior to writing the pp command. the host system must drive cs# low, and then write the be command on si . cs# must be driven low for the entire duration of the be sequence. the command sequence is shown in figure 9.10 and table 9.4 on page 23 . the host system must drive cs# high after the device has latched the 8th bit of the ce command, otherwise the device does not execute the co mmand. the be operation begins as s oon as cs# is driven high. the device internally controls the timing of th e operation, which requires a period of t be . the status register may be read to check the value of the write in progress (w ip) bit while the be operation is in progress. the wip bit is 1 during the be operation, and is 0 when the oper ation is completed. the device internally resets the write enable latch to 0 before the operation co mpletes (the exact timing is not specified). the device only executes a be command if al l block protect bits (bp2:bp0) are 0 (see table 7.1 on page 12 ). otherwise, the device ignores the command. figure 9.10 bulk erase (be) command sequence 9.11 deep power down (dp) the deep power down (dp) command provides the lo west power consumption m ode of the device. it is intended for periods when the device is not in active use, and ignores all commands except for the release from deep power down (res) command. the dp mode therefore provides the maximum data protection against unintended write operations. the standard standby mode, which th e device goes into automatically when cs# is high (and all operations in progress are complete), should generally be used for the lowest power consumption when the quickest return to device activity is required. the host system must drive cs# low, and then write th e dp command on si. cs# must be driven low for the entire duration of the dp sequence. the command sequence is shown in figure 9.11 and table 9.4 on page 23 . the host system must drive cs# high after the device has latched the 8th bit of the dp command, otherwise the device does not execute the command. after a delay of t dp, the device enters the dp mode and current reduces from i sb to i dp (see table 14.1 on page 26 ). once the device has entered the dp mode, all commands are ignored except the res command (which releases the device from the dp mode). the res comm and also provides the electronic signature of the device to be output on so, if desired (see section 9.12 and 9.12.1) . dp mode automatically terminates when power is remov ed, and the device always powers up in the standard standby mode. the device rejects any dp command issued while it is executing a program, erase, or write status register operation, and c ontinues the operation uninterrupted. 01 2 4 56 7 comm a nd c s # s ck s i 3 s o hi-z mode 0 mode 3
22 s25fl008a s25fl008a_00_b3 february 27, 2009 data sheet figure 9.11 deep power down (dp) command sequence 9.12 release from deep power down (res) the device requires the release from deep power down (res) command to exit the deep power down mode. when the device is in the deep power do wn mode, all commands except res are ignored. the host system must drive cs# low and write the res command to si. cs# must be driven low for the entire duration of the sequence. the command sequence is shown in figure 9.12 and table 9.4 on page 23 . the host system must drive cs# high t res(max) after the 8-bit res command byte. the device transitions from dp mode to the standby mode after a delay of t res (see table 16.1 on page 27 ). in the standby mode, the device can execute any read or write command. figure 9.12 release from deep power down (res) command sequence c s # s ck s i s o s t a nd b y mode deep power-down mode comm a nd 0 1 2 3 4567 t dp hi-z mode 0 mode 3 c s # s ck s i s o 0 1 2 3 4 5 6 7 comm a nd deep power-down mode t re s s t a nd b y mode mode 0 hi-z mode 3
february 27, 2009 s25fl008a_00_b3 s25fl008a 23 data sheet 9.12.1 release from deep power down and read electroni c signature (res) the device features an 8-bit el ectronic signature, which can be read using the res command. see figure 9.13 and table 9.4 on page 23 for the command sequence and si gnature value. the electronic signature is not to be confused with the identifica tion data obtained using the rdid command. the device offers the electronic signature so th at it can be used with previous devices that offered it; however, the electronic signature should not be used for new designs, which should read the rdid data instead. after the host system drives cs# low, it must write the res command follo wed by 3 dummy bytes to si (each bit is latched on si during the rising edge of sck). the electronic signature is then output on so; each bit is shifted out on the falling edge of sc k. the res operation is terminated by driving cs# high after the electronic signature is read at least once. additional clock cycles on sck with cs# low cause the device to output the electronic si gnature repeatedly. when cs# is driven high, the device transitions from dp mode to the standby mode after a delay of t res , as previously described. the res command always provides access to the electronic signature of the device and can be applied even if dp mode has not been entered. any res command issued while an erase, program, or wrsr operation is in progress not executed, and the operation continues uninterrupted. figure 9.13 release from deep power down and read elec tronic signature (res) command sequence notes 1. the s25fl008a has a manufacturer id of 01h, and a device id co nsisting of the memory type (02h) and the memory capacity (13h) . 2. the s25fl008a has an electr onic signature id of 13h. table 9.4 command definitions operation command description one-byte command code address bytes dummy byte data bytes read read read data bytes 03h (0000 0011) 3 0 1 to fast_read read data bytes at higher speed 0bh (0000 1011) 3 1 1 to rdid read identification (note 1) 9fh (1001 1111) 0 0 1 to 3 write control wren write enable 06h (0000 0110) 0 0 0 wrdi write disable 04h (0000 0100) 0 0 0 erase se sector erase d8h (1101 1000) 3 0 0 be bulk (chip) erase c7h (1100 0111) 0 0 0 program pp page program 02h (0000 0010) 3 0 1 to 256 status register rdsr read from status register 05h (0000 0101) 0 0 1 to wrsr write to status register 01h (0000 0001) 0 0 1 power saving dp deep power down b9h (1011 1001) 0 0 0 res release from deep power down abh (1010 1011) 0 0 0 release from deep power down and read electronic signature (note 2) abh (1010 1011) 0 3 1 to c s # s ck s i s o 3 d u mmy byte s hi-z m s b deep power-down mode s t a nd b y mode 0 1 2 3 4567 8 9 10 2 8 29 3 0 3 1 3 2 33 3 4 3 5 3 6 3 7 38 electronic id o u t comm a nd t re s 2 3 22 21 3 2 10 7 65 4 3 2 1 0 m s b
24 s25fl008a s25fl008a_00_b3 february 27, 2009 data sheet 10. power-up and power-down during power-up and power-down, certain conditions mu st be observed. cs# must follow the voltage applied on v cc , and must not be driven low to select the device until v cc reaches the allowable values as follows (see figure 10.1 and table 10.1 on page 24 ): ? at power-up, v cc (min) plus a period of t pu ? at power-down, v ss a pull-up resistor on chip select (cs#) typically meets proper power-up and power-down requirements. no write status register, progr am, or erase command should be sent to the device until v cc rises to the v cc min, plus a delay of t pu . at power-up, the device is in standby mode (not deep power down mode) and the wel bit is reset (0). each device in the host system should have the v cc rail decoupled by a suitable capacitor close to the package pins (this capacitor is generally of the or der of 0.1 f), as a precaution to stabilizing the v cc feed. when v cc drops from the operating voltage to below the minimum v cc threshold at power-down, all operations are disabled and the device does not res pond to any commands. note that data corruption may result if a power-down occurs while a write regi ster, program, or erase operation is in progress. figure 10.1 power-up timing diagram 11. initial delivery state the device is delivered with all bits set to 1 (each byte contains ffh) upon initial factory shipment. the status register contains 00h (all status register bits are 0). table 10.1 power-up timing characteristics symbol parameter min max unit v cc(min) v cc (minimum) 2.7 v t pu v cc (min) to device operation 10 ms v cc v cc (max) v cc (min) full device access t pu time
february 27, 2009 s25fl008a_00_b3 s25fl008a 25 data sheet 12. absolute maximum ratings do not stress the device beyond the ratings listed in this section, or serious, permanent damage to the device may result. these are stress ratings only and device oper ation at these or any other conditions beyond those indicated in this section and in the operating ranges section of this document is not implied. device operation for extended periods at the limits listed in this section may affect device reliability. notes 1. minimum dc voltage on input or i/o pins is ?0.5 v. during voltage transitions, inputs or i/o pins may overshoot v ss to ?2.0 v for periods of up to 20 ns. see figure 12.1 . maximum dc voltage on output and i/o pins is 3.6 v. during voltage transitions outputs may overshoot to v cc + 2.0 v for periods up to 20 ns. see figure 12.2 . 2. no more than one output may be shorted to ground at a time. duration of the short circuit should not be greater than one seco nd. 3. stresses above those listed under absolute maximum ratings may cause permanent damage to the de vice. this is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this d ata sheet is not implied. exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability. figure 12.1 maximum negative overshoot waveform figure 12.2 maximum positive overshoot waveform 13. operating ranges note operating ranges define those limits between wh ich functionality of the device is guaranteed. 14. dc characteristics this section summarizes the dc char acteristics of the device. designers should check that the operating conditions in their circuit match the measurement c onditions specified in the test specifications in table 15.1 on page 26 , when relying on the quoted parameters. table 12.1 absolute maximum ratings description rating ambient storage temperature ?65c to +150c voltage with respect to ground: all inputs and i/os ?0.5 v to v cc +0.5 v 20 ns 20 ns +0.8 v ?0.5 v 20 ns ?2.0 v 20 ns 20 ns v cc +2.0 v v cc +0.5 v 20 ns 2.0 v table 13.1 operating ranges description rating ambient operating temperature (t a ) industrial ?40c to +85c positive power supply voltage range 2.7 v to 3.6 v
26 s25fl008a s25fl008a_00_b3 february 27, 2009 data sheet note typical values are at t a = 25 c and 3.0 v. 15. test conditions figure 15.1 ac measurements i/o waveform table 14.1 dc characteristics (cmos compatible) parameter description test conditions (see note) min typ. max unit v cc supply voltage 2.7 3 3.6 v i cc1 active read current sck = 0.1 v cc /0.9v cc 33 mhz 9 ma sck = 0.1 v cc /0.9v cc v cc = 3.0v 50 mhz 13 ma i cc2 active page program current cs# = v cc 16.5 27 ma i cc3 active wrsr current cs# = v cc 24 ma i cc4 active sector erase current cs# = v cc 24 ma i cc5 active bulk erase current cs# = v cc 24 ma i sb standby current v cc = 3.0 v cs# = v cc 20 50 a i dp deep power down current v cc = 3.0 v cs# = v cc 1.5 5 a i li input leakage current v in = gnd to v cc 1a i lo output leakage current v in = gnd to v cc 1a v il input low voltage ?0.3 0.3 v cc v v ih input high voltage 0.7 v cc v cc + 0.5 v v ol output low voltage i ol = 1.6 ma, v cc = v cc min 0.4 v v oh output high voltage i oh = ?0.1 ma v cc ? 0.2 v table 15.1 test specifications symbol parameter min max unit c l load capacitance 30 pf input rise and fall times 5 ns input pulse voltage 0.2 v cc to 0.8 v cc v input timing reference voltage 0.3 v cc to 0.7 v cc v output timing reference voltage 0.5 v cc v 0. 8 v cc 0.2 v cc 0.7 v cc 0. 3 v cc inp u t level s inp u t a nd o u tp u t timing reference level s 0.5 v cc
february 27, 2009 s25fl008a_00_b3 s25fl008a 27 data sheet 16. ac characteristics notes 1. typical program and erase times assume the following conditions: 25c, v cc = 3.0 v; 10,000 cycles; checkerboard data pattern 2. under worst-case conditions of 90 c; v cc = 2.7 v; 100,000 cycles 3. not 100% tested figure 16.1 ac characteristics symbol (notes) parameter min typ (notes) max (notes) unit f sck sck clock frequency read command d.c. 33 mhz f sck sck clock frequency for: fast_read, pp, se, be, dp, res, wren, wrdi, rdsr, wrsr d.c. 50 mhz t crt clock rise time (slew rate) 0.1 v/ns t cft clock fall time (slew rate) 0.1 v/ns t wh sck high time 9 ns t wl sck low time 9 ns t cs cs# high time 100 ns t css (3) cs# setup time 5 ns t csh (3) cs# hold time 5 ns t hd (3) hold# setup time (relative to sck) 5 ns t cd (3) hold# hold time (relative to sck) 5 ns t hc hold# setup time (relative to sck) 5 ns t ch hold# hold time (relative to sck) 5 ns t v output valid 10 ns t ho output hold time 0 10 ns t hd:dat data in hold time 5 ns t su:dat data in setup time 5 ns t r input rise time 5ns t f input fall time 5ns t lz (3) hold# to output low z 10 ns t hz (3) hold# to output high z 10 ns t dis (3) output disable time 10 ns t wps (3) write protect setup time 15 ns t wph (3) write protect hold time 15 ns t w write status register time 67 150 ms t dp cs# high to deep power down mode 3 s t res release dp mode 30 s t pp page programming time 1.5 (1) 3 (2) ms t se sector erase time 0.5 (1) 3 (2) sec t be bulk erase time 6 (1) 48 (2) sec
28 s25fl008a s25fl008a_00_b3 february 27, 2009 data sheet figure 16.2 spi mode 0 (0,0) input timing figure 16.3 spi mode 0 (0,0) output timing figure 16.4 hold# timing c s # s ck s i s o t c s h t c ss t c s h t c ss t crt t cft m s b in l s b in hi-z t s u:dat t hd:dat t c s c s # s ck s o l s b out t wh t wl t di s t v t ho t v t ho t ch t hz t cd t hd t hc t lz c s # s ck s o s i hold#
february 27, 2009 s25fl008a_00_b3 s25fl008a 29 data sheet figure 16.5 write protect setup and hold timing during wrsr when srwd=1 w# c s # s ck s i s o hi-z t wp s t wph
30 s25fl008a s25fl008a_00_b3 february 27, 2009 data sheet 17. physical dimensions 17.1 soc 008 wide?8-pin plastic small outline 208 mils body width package 3432 \ 16-038.03 \ 10.28.04 notes: 1. all dimensions are in both inches and millmeters. 2. dimensioning and tolerancing per asme y14.5m - 1994. 3. dimension d does not include mold flash, protrusions or gate burrs. mold flash, protrusions or gate burrs shall not exceed 0.15 mm per end. dimension e1 does not include interlead flash or protrusion interlead flash or protrusion shall not exceed 0.25 mm per side. d and e1 dimensions are determined at datum h. 4. the package top may be smaller than the package bottom. dimensions d and e1 are determined at the outmost extremes of the plastic body exclusive of mold flash, tie bar burrs, gate burrs and interlead flash. but including any mismatch between the top and bottom of the plastic body. 5. datums a and b to be determined at datum h. 6. "n" is the maximum number of terminal positions for the specified package length. 7. the dimensions apply to the flat section of the lead between 0.10 to 0.25 mm from the lead tip. 8. dimension "b" does not include dambar protrusion. allowable dambar protrusion shall be 0.10 mm total in excess of the "b" dimension at maximum material condition. the dambar cannot be located on the lower radius of the lead foot. 9. this chamfer feature is optional. if it is not present, then a pin 1 identifier must be located within the index area indicated. 10. lead coplanarity shall be within 0.10 mm as measured from the seating plane. . package soc 008 (inches) soc 008 (mm) jedec symbol min max min max a 0.069 0.085 1.753 2.159 a1 0.002 0.0098 0.051 0.249 a2 0.067 0.075 1.70 1.91 b 0.014 0.019 0.356 0.483 b1 0.013 0.018 0.330 0.457 c 0.0075 0.0095 0.191 0.241 c1 0.006 0.008 0.152 0.203 d 0.208 bsc 5.283 bsc e 0.315 bsc 8.001 bsc e1 0.208 bsc 5.283 bsc e .050 bsc 1.27 bsc l 0.020 0.030 0.508 0.762 l1 .055 ref 1.40 ref l2 .010 bsc 0.25 bsc n 8 8 0? 8? 0? 8? 1 5? 15? 5? 15? 2 0? 0? 9 c a a1 a2 b e 5 b d e e/2 5 e1/2 4 3 e1 3 seating plane 4 d a 0.10 0.10 a-b 0.20 c a-b c c c md 0.25 0.33 c h see detail b b1 c1 7 (b) c with plating base metal section a-a 2 0.07 r min. 1 l1 c l2 a a l gauge plane seating plane h detail b q q q
february 27, 2009 s25fl008a_00_b3 s25fl008a 31 data sheet 17.2 uson 8l (5 x 6 mm) no-lead package 3448\ 16-038.28 \ 04.19.05 notes: 1. dimensioning and tolerancing conforms to asme y14.5m-1994. 2. all dimensions are in millimeters, 0 is in degrees. 3. n is the total number of terminals. 4. dimension b applies to metallized terminal and is measured between 0.15 and 0.30 mm from terminal tip. if the terminal has the optional radius on the other end of the terminal, the dimension b should not be measured in that radius area. 5. nd refers tot he number of terminals on d side. 6. maximum package warpage is 0.05 mm. 7. maximum allowable burrs is 0.076 mm in all directions. 8. pin #1 id on top will be laser marked. 9. bilateral coplanarity zone applies to the exposed heat sink slug as well as the terminals. quad flat no lead packages (une) - plastic dimensions symbol min nom max note e 1.27 bsc n 8 3 nd 4 5 l 0.55 0.60 0.65 b 0.35 0.40 0.45 4 d2 3.90 4.00 4.10 e2 3.30 3.40 3.50 d 5.00 bsc e 6.00 bsc a 0.45 0.50 0.55 a1 0.00 0.02 0.05 k 0.20 min. 0 --- 12 2
32 s25fl008a s25fl008a_00_b3 february 27, 2009 data sheet 18. revision history section description revision a (october 28, 2004) global initial release. revision a1 (march 2, 2005) global updated trademark information. ordering information added commercial temperature range. added package and temperature designators. added note for pb-free and non-pb free package physical dimensions updated wson 8-contact no-lead package drawing. revision a2 (march 30, 2005) global updated table 7. removed commercial temperature range. changed wson package nomenclature to uson package; updated uson package dimensions. added tray option for packing type. revision a3 (august 31, 2005) global updated ordering information. added tape and reel option for packing type. updated tables 8 and 10. added tray option for packing type. revision a4 (may 19, 2006) global removed preliminary document status. revision a5 (june 29, 2006) dc characteristics added typical specificat ion and changed maximum specification for i cc2 . revision b0 (august 31, 2006) global rewrote entire document for better flow and clarity. no specifications were changed. revision b1 (february 19, 2007) absolute maximum ratings added overshoot/undershoot spec operating ranges removed commercial option revision b2 (june 29, 2007) device operations added a sentence to byte or page programming revision b3 (february 27, 2009) global added obsolescence information to cover sheet , distinctive characteristics, and ordering information sections of data sheet.
february 27, 2009 s25fl008a_00_b3 s25fl008a 33 data sheet colophon the products described in this document are designed, developed and manufactured as contemplated for general use, including wit hout limitation, ordinary industrial use, genera l office use, personal use, and household use, but are not designed, developed and m anufactured as contemplated (1) for any use that includes fatal risks or dangers t hat, unless extremely high safety is secured, could have a s erious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic contro l, mass transport control, medical life support system, missile launch control in we apon system), or (2) for any use where chance of failure is intole rable (i.e., submersible repeater and artifi cial satellite). please note that spansion will not be liable to you and/or any third party for any claims or damages arising in connection with abo ve-mentioned uses of the products. any semic onductor devices have an inherent chance of failure. you must protect agains t injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. if any products described in this document r epresent goods or technologies s ubject to certain restriction s on export under the foreign exchange and foreign trade law of japan, the us export ad ministration regulations or the applicable laws of any oth er country, the prior authorization by the respective government entity will be required for export of those products. trademarks and notice the contents of this document are subjec t to change without notice. this document ma y contain information on a spansion product under development by spansion. spansion reserves the right to change or discontinue work on any product without notice. the informati on in this document is provided as is without warran ty or guarantee of any kind as to its accuracy, completeness, operability, fitness for particular purpose, merchantability, non-infringement of third-party rights, or any other warranty, express, implied, or statutory. spansion assume s no liability for any damages of any kind arising out of the use of the information in this document. copyright ? 2004-2009 spansion inc. all rights reserved. spansion ? , the spansion logo, mirrorbit ? , mirrorbit ? eclipse ? , ornand ? , ornand2 ? , hd-sim ? , ecoram ? and combinations thereof, are trademarks of spansi on llc in the us and other countries. other names used are for informational purposes only and ma y be trademarks of their respective owners.

▲Up To Search▲

Price & Availability of S25FL008A0LNFI000

	To Download S25FL008A0LNFI000 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .